Before you remove the Feed Roller Parts, you should remove: - Pick Up Roller Ass'y Refer to 5. White vertical stripes on thewhole screen or partly : Check the weight of thedeveloper. Straight thin black vertical line occurs in the printing. Open the document cover and turn the release knobto remove the misfed documents from the documentdocument output tray. Before remov-ing any component from the machine, note thecable routing that will be af fected. Unfold the duplex guide fully. Run Self-Test to remove the contamination of the transfer roller.
These settings are are remembered after memory delete Clear All Memory. Before you remove the Fuser Drive Ass'y, you should remove:- Rear Cover Refer to 5. The example list is for an average usage of 50 transmitted and received documents per day. If the supply of +24v is unstable in the Main Control board 1. Replace the toner cartridge and close the front cover. If you connect your printer using the network cable, skip to the next step. If the transfer roller is contaminated, stains 2.
Check the Network printer, and select your printer from the drop-down list. The main product concept is ° High Speed and High Quality. The name of printer is displayed empty while 1. The required condition is 20° C to 24° C 68° F to 75° F , with a relative humidity of 4 percent to 55 percent. If light or dark periodical blackdots occur, this is because thedeveloper rollers are contami -nated with foreign substanceor paper particles. In this case, enter the each fax number.
Check and Cause Solution 1. Activating this mode extends the life of the toner cartridge longer than the normal mode, but it reduces the print quality. Split the transmission into more than Divide the Job one operation. Pull the jammed paper out. It is possible to begin typing the number on the number pad without first selecting fax mode.
Check if copy function operates normally. Remove the Jam Link Lever L,R and Jam Holder L,R and then remove the Pressure Roller, asshown below. Use the lifting handles located on each side of the machine. You can temporarily reestablish the print quality by redistributing the remaining toner in the cartridge. Make sure the printer is configured in SyncThru using the new name. Check and Cause Solution 1. This tray holds 250 sheets of paper.
Exploded Views and Parts List8. Remove the two screws securing the both side of theHalogen Lamp and then release in the direction ofarrow, as shown below. The time the machine was first used is remembered. Pull the Tray Links from the both side of the FrontCover with a light pressure to the direction of arrow. After installation, double check that the printer is stable. Replace a damaged power cable immediately , do not reuse or repair the damaged cable. To continue to the next step, press Select when Done appears.
Check and Cause Solution 1. Split the transmission into more thanDivide the Job one operation. Environmental conditions and actual use will may vary. In case of 2 - If there are any abnormals inconnection with the situation of 1. If the document is jammed in the paper feed area: a. Idle Gear Bracket E-Ring Retard Gear T2 Idle Gear Notice : Be aware of the E-Ringsto ensure they are not lost. Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer 75.
Open and close the front cover to resume printing. Manual Sen Test state normal or not of the Sensors. To use the bypass tray: 1. But upgrading is not executed. Check the assemblage and perfor- mance of the exit.
For Windows Vista, click Control Panel Hardware and Sound Printers. Pull the paper straight up and out. Document Width75, 300, 600dpi horizontalfor only optical resolutionMax. Check the right position of the Scanner Motor , and disturbance. Page What if I purchased a service contract? Remember to change the paper size setting when you use a source that does not support auto size sensing.
Recycled recording paper has been used. Insert the paper stack into the paper tray with the side to be printed on, facing down. If the package accompanying your Dell computer or device contains optical discs or other storage media, you may use only the media appropriate for your computer or device. Over Heat There is a problem in the fuser unit. Check the Motor harness, replace it, if defective.