Hummer h1 parts manual. Us Army Hmmwv Hummer Humvee Military Manuals 2019-01-25

Hummer h1 parts manual Rating: 8,8/10 464 reviews

Hummer Parts Guy (HPG)

hummer h1 parts manual

Remove three screws and drainage bracket from body Figure 3-29. Electric Drive, Thermal Cutoff Switch Capacity. Remove two bolts and clamps securing winch cables to winch. Install drum assembly on gear train assembly. Disconnect the by a switch in the passenger compartment. This will avoid losing or mispositioning the The following electrical components can be replaced once the check-balls. The valve limits pressure buildup in the oil cooler and Install fill tube seal in transmission.

Next

Us Army Hmmwv Hummer Humvee Military Manuals

hummer h1 parts manual

Fourth Overrun Roller Direct Front Sprag Interm. If you ever lose your service manual just contact us we will send to you the service manual within 24 hours for free for lifetime. Remove access plug and washer from geared hub Figure 9-15. Position joint inner housing over bearing assembly. The solenoid valve energizes or de-energizes by making or breaking an electrical circuit through a combination Perform this test before a road test in order to make sure that of switches and sensors. Install new seal in front cover with installer tool Jā€”22102. Open hood and loosen center hood stop Figure 10-85.

Next

Humvee Parts

hummer h1 parts manual

Be sure side-to-side variation does not exceed 0. Use a soap and water solution to on the Deflate Valve check for leaks. Only the pump solenoids, sensors, gaskets, and drive gears are 2. Check for kinks in hose. .

Next

HUMMER H1 6.5L DETROIT DIESEL FULL WORKSHOP REPAIR MANUAL

hummer h1 parts manual

Remove fill plug and washer from geared hub Figure 9-40. Remove two locknuts, washers, bolts, and washers Installation securing front suspension brace to frame extension. Install the J 39775 jumper on the transmis- 19-24ā„¦ 20Ā° Go to step 3 Go to step 2 sion 20 way connector. Four Cycle, Turbocharged Diesel, Liquid-Cooled Power Output:. Disconnect driver side fuel injector lines at pump and injectors and remove lines.

Next

HUMMER H1 6.5L DETROIT DIESEL FULL WORKSHOP REPAIR MANUAL

hummer h1 parts manual

Install housing on pump body. Gently close hood and loosen lower hinge half locknuts Figure 10-86. It Can be viewed on any laptop, computer, cell phone, ipad, tablet, any smart device. Ā„ Engine wire harness clips and ground wires 13. Install intermediate gear carrier on gear housing.

Next

Hummer H1 Parts & Accessories

hummer h1 parts manual

Before final tightening of the sleeve clamp hardware, center both tie rod end studs in their sockets Figure 8-5. Remove U-bolts, attaching rear shaft to rear axle yoke 10. Inspect outside of tire for sidewall damage. Remove brake caliper and rotor. Retighten the inner 12 mm bolts to 55 lb-ft 75 N.

Next

Hummer H1 Parts & Accessories

hummer h1 parts manual

Remove and disassemble differential as follows: Scribe or paint mark front and rear cases for assembly reference Figure 5-110. Remove stem seal from valve and slide valve out of guide and head. The front and rear output Hummer vehicles are equipped with the New Process Gear, drive sprockets are interconnected by a drive chain model 242 transfer case. Diesel Injection Line Bracket And Clamp Install bracket on valve cover studs Figure 3-51. Take advantage of our full service restoration services. Remove spacer, insulator, and washer from brush assembly power stud. For information regarding inlet pipes, Installation refer to Section 3.

Next

HUMMER H1 6.5L DETROIT DIESEL FULL WORKSHOP REPAIR MANUAL

hummer h1 parts manual

Connect injection lines to pump Figure 3-55. . The repair procedures described in this section cover engine service that can be performed in the vehicle. Inspect inner rim for cracked, broken, rusted, pitted, bent, or loose studs, and studs with damaged, mutilated, or deformed threads. The lifters are not repairable. Remove soft top or loosen roof assembly, as applicable. Insert thrust screw in caliper and seat it on centering pin and on ball bearings.

Next