Check if the washer is perfectly level as follows:Check the leveling of the washer with a leveland check that the washer is stable. For example, when set to a quick wash for 28 minutes, you come back 20 or 30 minutes later and it still says 20 minutes left. When the machine is spinning at high speed,verify that it is stable. If you can hear the motor turning during the spin cycle, the pump should be working. Be sure to check the pump and tub sump for foreign objects before replacing pump. Inspect the motor coupling to determine if it is broken. If visual check fails, reconnect P4 and repeat step 1.
. If the hot water system has not been requirements. It is 11+ years old. Do not crossthread when connecting the inlet hose to the valve. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. Disassemble the clamps and hoses. This manual books file was hosted in www.
Is there any way to force the washer to just fill up and stop dribbling? You could also try the manufacturer's web site direct but some manufacturers will only supply to their engineers ;-0 If this has assisted you please consider a 4 thumbs up for the rating. Posted on Jan 31, 2017 The packets usually have detergent and rinse aid together, built in. Run the washer with a test load to make certain your washer is properly leveled. If the supply cord is damaged, it must be replaced by a qualified person in order to avoid a hazard. If resistance values are good, go to step 7. Failure to do so can result in fire.
That was a waste of time, as the water inlet valve is behind the screen, and there is no way to get to the filter. The dispenser should be cleaned periodically to remove buildup from detergent and other laundry products. Periodically check the condition of the hose and replace the hose if necessary. Kind Regards :- If you found this solution helpful, please rate it. Concerning the power cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Do you know what it might be? Two or more people may be needed to install and move the appliance.
Failure to follow this warning can cause serious injury, fire, electric shock or death. Remove the connector at the motor and take measurements across pump terminals. Connect the inlet hose firmly to prevent leak. First, see the following Whirlpool Kenmore installation and service manual for top load, direct drive washers. Take out the 4 bolts by twisting the braces slightly Keep the 4 bolts and the wrench for future use Whenever the appliance is transported, the shipping bolts and braces must be replaced.
Please leave a comment below and we will be happy to assist. Press the Start button repeatedly to cycle through the test modes. Companion appliance spacing should also be considered. Tilt machine forward to access the bottom of the machine and the pumps 6. I had a service technician come out while it was still under warranty. To use this feature, after the load has been removed, do not close the door completely. This is definitely advantageous when you compare this with the competition.
Where can I find more information on this? In case of any Do not wash Hot ironing Hang to dry Do not bleach failure, first unplug the machine and turn off the water tap. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed. Fred Bicknell July 4, 2017 at 1:58 am Problem solved. Thanks for the the tip Fred! Inability of opening the Door during mid cycle takes away freedom of the washer and hence consumers shy away from buying Front Load Washing Machine. If the drive belt is broken or loose, replace it.
If resistance values are good, go to step 7. Do not submerge the end of the hose. The motor coupling can also fail due to normal wear. Turn on the water tap Remove any clothing or items on the flexible gasket - to prevent clothing and the gasket damages. It seems to just quit during the cycle. Large items should not be more than half the total wash load. The and hoses may be the next step.
Repair or replace the lower wiring harness. Do not wash single items. First, check the connection of each electrical terminal with the wiring diagram. Cause 2 Motor Coupling The motor coupling connects the motor to the washer transmission. Perform the following checks if washer fails to drain or recirculate.