Pentair intelliflo installation manual. Pentair INTELLIFLO VS 2019-02-19

Pentair intelliflo installation manual Rating: 6,1/10 1947 reviews

Pool and Spa Product Manuals and Specs

pentair intelliflo installation manual

The pump requires little or during disassembly and reassembly. If this alarm persists, contact Pentair Technical Service at 1-800-831-7133. To on the pump cannot be disabled by the external disable, press Select. Inside there is a basket which must be kept clean of leaves and debris at all times. Call 800 831-7133for additional free copies of these instructions. The pump provides an automatic internal cutoff switch to protect the motor from heat damage during operation. Note: Turn off power to unit prior to attempting service or repair.

Next

Pumps

pentair intelliflo installation manual

Close the EasyTouch Control System load center front door. This mode is identical to Feature 1 and 2 except that you can manually start this mode using the Vacuum button. To unscrew the impeller from the shaft, twist the impeller counterclockwise. We offer the broadest line of pressure side, suction side and robotic cleaners in the world so no matter your cleaning challenge or budget, there's always one right for your pool. Close the control panel into its original position and secure it with the two access screws. The pump system clock controls all scheduled start and stop times, functions, and programmed cycles.

Next

Pentair INTELLIFLO VS

pentair intelliflo installation manual

Variable Speed Pump goes into Thermal Mode. Fasten the two spring latches. For more about using the speed buttons, see page 5. Note that IntelliTouch will not start communicating with the IntelliFlo until the pump is assigned to a circuit. Therefore, if small suction outlets are used with this pump, to prevent this entrapment and possible death, install at least two suction outlets in the body of water. Your builder will help you select the brushes and poles, hand skimmers, leaf rakes and traps, and thermometers to keep your pool sparkling clean and ready to go.

Next

PENTAIR INTELLIFLO VS+SVRS INSTALLATION AND USER MANUAL Pdf Download.

pentair intelliflo installation manual

For added protection, a slinger located in front of the main shaft seal assists in slinging water away from the shaft opening in the flange. Use the Up arrow button. To edit this setting, see step 6. Loosen the two access screws securing the control panel. It is absolutely critical that the suction plumbing be installed in accordance with the latest national and local codes for swimming pools. It may take several minutes to prime depending on the depth of water, pipe size and length.

Next

Pentair Instruction Manuals

pentair intelliflo installation manual

Note: Do not install this pump within an outer enclosure or 15. Note: Multiple wires may be inserted into a single screw terminal. In fact, with our IntelliChlor chlorine generator, you'll never need to buy, transport, handle or store chlorine again, because it turns ordinary table salt into chlorine, right in your pool. The drive microprocessor controls the motor by changing the frequency of the current it receives together with changing the voltage to control the rotational speed. Remove the rotating portion of the mechanical seal from the impeller. .

Next

Pentair INTELLIFLO VS

pentair intelliflo installation manual

Once the pump achieves prime, it will resume Note: Quick Clean is the only high-speed override normal operation after the preset priming delay. This process evacuates the air from all the suction lines and the pump. Problem Possible Cause Corrective Action Pump failure. In this configuration, EasyTouch control system starts, stops and controls the speed of the pump. The default setting is two 2 minutes.

Next

PENTAIR INTELLIFLO INSTALLATION AND USER MANUAL Pdf Download.

pentair intelliflo installation manual

Using the control panel, IntelliFlo can use one of the four selectable preset speeds or the pump speed can be adjusted to run at a specific speed. To access the Password menu: 1. This process evacuates the air from all the suction lines and the pump. Press Save to save the new stop time setting. There are four preset speed buttons that can be selected. Those names and brands may be the trademarks or registered trademarks of those third parties.

Next

Pool and Spa Product Manuals and Specs

pentair intelliflo installation manual

Retaining screw EasyTouch Load Center front view Control panel access screw Control panel access screw High voltage cover panel. This document is subject to change without notice. Route the communication cable into the lower plastic grommet, up through the low voltage raceway to the EasyTouch system load center motherboard. Unlatch the two enclosure door spring latches, and open the door. Canadian applications other than for which the pump was intended can result in severe personal injury or death.

Next