Service manual gilera nexus 500. Reading : Gilera Nexus 500 Euro 3 Scooter Service Repair Manual 2019-03-18

Service manual gilera nexus 500 Rating: 8,1/10 1892 reviews

Gilera Nexus 500 Workshop Service Repair Manual

service manual gilera nexus 500

Check the connections to the electric fan, the function of the contacts of the remote control switch, the positive lines, the negative line and the motor of the electric fan. Specific tooling 020376Y Adaptor handle 020456Y Ø 24 mm adaptor 020363Y 20 mm guide N. Detach the electrical connector from the pump support with the engine running and wait for the shutdown. Engine stop remote control 19. The stepper is powered by the control unit only when the opening must be changed.

Next

Reading : Gilera Nexus 500 Euro 3 Scooter Service Repair Manual

service manual gilera nexus 500

Personal safety Failure to completely observe these instructions will result in serious risk of personal injury. The new stand differs from the old stand in having a 5 mm longer stand arms, increasing the height of the scooter from the ground. Install the fuel pressure check kit special tool. The sensor allows the control unit to optimise the engine performance based on altimetric variations. Remove the starter motor see the flywheel and starter system. Wait for one minute, making sure there are no leaks coming from the injector.

Next

Reading : Gilera Nexus 500 Euro 3 Workshop Manual

service manual gilera nexus 500

In these conditions, the engine works, even though not in an optimum way, always safeguarding the catalytic converter integrity. One way is connected to the pump and the other to the radiator of the horizontal circulation type. Reproduction of this publication in whole or in part is prohibited. When refitting the battery onto the scooter pay attention not to invert the cables, bearing in mind that the earth black wire marked with a - must be connected to the negative terminal whilst the other two red wires, marked with a + must be attached to the positive, + terminal. In the other cases, the engine works managed by the basic data.

Next

Gilera Nexus 500SP Mk2 Workshop www.zenga.tv

service manual gilera nexus 500

Specific tooling 020460Y Scooter diagnosis and tester Make sure that the throttle valve with the control is supporting the stop screw. If the range drops below 40 km, the symbol appears automatically and flashes for 60 seconds. The engine can be started. It is realised with two electrically different sections. Check the component seals again, if necessary.

Next

Gilera Nexus 500 Workshop Service Repair Manual

service manual gilera nexus 500

Connections to the power supply source must be implemented by connecting corresponding poles + to + and - to -. Throttle valve opening sensor Throttle position sensor t. The keys can be stored to memory, the scooter can be started but with a limitation imposed on the number of revs. Lampada indicatore di direzione anteriore Sx 40. The protrusion, measured near the external edge of the disc, must be less than 0. The control unit data can be checked by the diagnostic tester. Check the control unit power supply.

Next

Reading : Gilera Nexus 500 Euro 3 Scooter Service Repair Manual

service manual gilera nexus 500

The engine rpm and the throttle valve position are the two basic signals for the engine management. This regulation must not be tampered with in any way whatsoever. Scroll the pages the find the data. Pump bracket installation - Before reassembling, carefully check the tank cleaning. To check the sensor and related circuit, proceed as follows: 1 - Connect the diagnostic tester.

Next

Gilera Nexus 500 Motorcycle REPAIR Manual 2005

service manual gilera nexus 500

If other voltages are measured or there is no alternation, replace the tone wheel. Since the wheel speed sensor is pivoted on the camshaft it is also possible to recognise the 4-stroke cycle. When the battery is charged, you should detect a density of 30 to 32 BĂŠ corresponding to a specific weight of 1. Characteristic By-pass housing hole diameter: 13. Never mistake the codes 002011 movement sensor replacement and 005089 tone wheel replacement in the event of noise of the indicated components. Specific tooling 020458Y Puller for lower bearing on steering tube Refitting Reassembly of tapered bearing in steering tube - Insert the a new plate and a new dust guard in the steering tube - Insert the a new tapered bearing in the steering tube - Using the special tool and a mallet to move the dust guard and the bearing in abutment. Front brake disc Removal - Remove the front wheel.

Next

Gilera Nexus 500SP Mk2 Workshop www.zenga.tv

service manual gilera nexus 500

The battery disconnection does not delete stored data. Front left light assembly B. Remove the hub cover and the relevant gasket. Characteristic Minimum width: 25 mm Standard width: 26. The light remains on during the period the cycle is reconstructed.

Next