Lift seat from the rear and slide backwards to disengage tongue— collect all fasteners for re-assembly. Remove the 2 allen-screws from rear seat section. Using this Triumph Trophy 900 1200 repair manual is an inexpensive way to keep you vehicle working properly. Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use. Simply print out the pages you need or print the entire manual as a whole!!! Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Always use caution and protect surfaces from spills whenever brake work is performed. Simple operations which can be performed easily just by looking at the vehicle i.
First you will have to make sure you have everything. Then you should be able to lift and pull the seat off. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. Lift sensor from the transmission case and set aside for later re-installation. Switchable wet and dry maps.
Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. Triumph Trophy 1200 Format: pdf Language: English Size: 2. Remove axle nut and washer—support or chock rear wheel—and slide out axle. In this application, the new clutch disc and pressure plate must be replaced as a pair. For all other models: Install previously removed wheel spacers.
In the original design, the oil tank was the oil filter since all particulate debris in the oil settled to the bottom of the oil tank as sediment. Read and follow all safety instructions. Hundreds of pages allow you to print it out in its entirety or just the pages you need!! Production model years 1993 1994 1995 1996 1997 1998. Models with Radio: Remove the radio. Afterwards, keep this Triumph Trophy 1200 Owners Manual in your vehicle so you can refer to it at any time.
Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Simply print out the pages you need or print the entire manual as a whole!!! Each section provides general information, specifications, diagrams, and service tools, where applicable. It is the same manual the Triumph Manual techs use to work on your car. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Remove both silencers from exhaust headers.
Drain the brake fluid from the front brake reservoir and lines per the instructions in the service manual. The Street Triple R also has a 675 cc engine, with a power output of 106 hp and six-speed transmission. This Triumph Trophy 900 1200 service manual is your number one source for repair and service information. Use your Allen wrench to remove both of these, there is one on each side. Remove the front brake master cylinder and clutch lever assemblies from the handlebar. Secure with flange lock nuts.
Suppliers can be contacted directly for any information not covered in this manual. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Disconnect battery and remove from motorcycle. Disc 1 covers Montero and Montero Sport. The tools you will need are a 5mm Allen wrench and a pair of pliers and a 10mm socket wrench. Remove the front brake line assembly. They also have a range of modern classics, roadsters and cruisers.
Disc 2 covers Eclipse, Eclipse Spyder and Galant. Pull the radio or storage box forward to remove it from the opening in the inner fairing. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Adjustable pit lane speed limiter and speedo calibration. Light sequencing begins with rear, programmable rear and front side lights, as well as front and 45 degree front lights. Next you will see two tabs that are turned over the gas tank.
Remove caliper and support so there is no strain on the brake line. Hundreds of pages allow you to print it out in its entirety or just the pages you need!! For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. Lift seat from the rear and slide backwards to disengage tongue— collect all fasteners for re-assembly. Support fender from beneath and remove the 4 Torx head screws— collect all fasteners for re-assembly. Earlier production for both series can be fitted with the new parts.