We pay for advertising across the web so customers can find their manual quick and easy for a small fee. EtherSound output channels 1—24 will be displayed. If soundcheck and rehearsal time allow, it is possible to create a scene snapshot for each song or act of the performance, including the preshow walk-inmusic and end show exit music and scenes for each support act too. The gate will open when the key-insignal exceeds this level, and will close when the signal falls below this level. The type of parameters that can be edited in this window depends on the type of the currently selected channel.
Each type has the following characteristics. B Comment Enter a comment for each user. You cannot save to Scene 000. The current value is shown in the numerical box below the knob. The current fader value is shown in the box below. You can set this to the default value +10 dB by holding down the key and clicking the knob.
B Fader Adjusts the input level of the input channel. The stereo bus setting can be made in Mix Bus Setup of the Mixer Setup screen. These channels are used to process monaural signals. As desired, connect your external equip-. The fader cap must be touched to allow the level to be adjusted.
EtherSound input channels 1—32 and 33—48 will be displayed. There are guides on how to connect there as well. This is used to send instructions from the mixer operator to the desired output channel. Double-clickthis to open the module editor for that rack unit. If this is successful, StageMix will re-synchronize with the console data and operation will become available again.
The channel name is shown in the boxes immediately below. The value set here is the time needed to wait between touching a fader and being able to move it. The channel name is shown in the boxes immediately below. It cannot be overwritten, nor can its title be edited. The scene number shows in the FunctionAccessArea and the goes out until another desk change is made. The corresponding scene will be recalled.
Summary of the content on the page No. You can set this to the center value by holding down the key of your computer keyboard and clicking this knob. Scene 000 is read only. If you change the patching in this window, the port that had been assigned until then will be cancelled, and only the newly selected port will be assigned. The date and time you specify here will affect the time stamp used when saving a scene. You can set this to the center position by holding down the key of the computer keyboard and clicking the knob.
The following table describes how to handle Sessions. When a fader cap is touched, its background will lighten and its current dB value will be displayed. White dots represent the position for each of the 31 bands. The current fader value is shown in the numeric box immediately below the fader. If Gate is assigned Dynamics 1 only , the status of the gate is shown immediately below the button. Our servers will always have what you need and give you download speeds up to 10 times Faster than most other companies! The input signal will start being compressed when the key-insignal exceeds this level; compression will be removed when the signal falls below this level.
Focus is another way of limiting the amount of information that is recalled when the chosen scene is recalled. The window includes the following items. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. Summary of the content on the page No. You can set this to the center value by holding down the key of your computer keyboard and clicking this knob.
Across the top of the screen, all Input, Mix and Matrix level meters and faders are displayed in blocks of eight. You can drag the numeric value up or down to edit the cutoff frequency. After you have read the manual, keep it in a safe place. Select the output port in the left side of the screen, and the input port in the right side of the screen. Do you have to be in the United States of America to order? If you cut and paste scenes they will change number.
This area displays a lock icon for protected scenes; these scenes cannot be overwritten, nor their title edited. Are you using a D-sub 9-pin cross cable? Scenes can be stored and recalled from the Master window, and scenes can be viewed in the Scene window just like the console. In a live recording set up it is required to have the mics connected to the channels of the scenes for recording, but for playback use the same scenes and have the recorder connected. We have meet all of these requirements set forth by the banks and Visa, Master Card, Discover and American Express. The current fader value is shown in the numeric box immediately below the fader.